HP t510 ThinPro 4.4 -> 5.1
I am trying to upgrade an HP t510 from ThinPro 4.4 to ThinPro 5.1. I know that the "ThinPro ThinState Addon (Service Pack) for 4.x" must be installed prior to the ThinPro 5.1 installation. I have two...
View ArticleZ840 ESXI installation Problem !
Hi , I need HP Z840 vmware esxi samsung Pcıe driver.I boot HP Z840 with Vmware ESXI 6.0.But Dont see local Samsung M2 ssd disk.How Can I this problem ? Thankyou very much.
View ArticleDoes anyone have the pin-outs for connectors P5 and front-audio of the Z210...
Does anyone have the pin-outs for connectors P5 and front-audio of the Z210 CMT system board ? Neither of these are documented in the HP Z210 CMT maintenance and service guide (appendix A, pages 154...
View ArticleRe: Does anyone have the pin-outs for connectors P5 and front-audio of the...
It looks like the P5 connector layout might be the same as on the Z620 as documented in this link If anyone knows for sure please say so.
View ArticleRe: 1065984 during install from HPDM version - 4.6 SP2
Looks like the repository is not well configured. Can you please let me know the "repospath" in the controller.conf, you should be able to find it at ..\HP Device Manager\MasterRepositoryContoller and...
View ArticleRe: HP t510 ThinPro 4.4 -> 5.1
I don't have a direct answer to your question, but I want to suggest you try HP Device Manager - management tool of HP thin Client, With HP Device Manager, you're able to upgrade ThinPro image...
View ArticleRe: T610 thin client gets stuck in PXE boot
Check if there is any PXE service running in the same subnet.Check if there is any DHCP option being configured in the same subnet. Try manually set the boot order from BIOS always set the "hard drive"...
View ArticleHP PROLIANT SERVER DL380 GEN9
HI, I am facing a problem during configuration of my new HP DL380 Gen9 Server. While i am using Built in setup utility Intelligent Management software i cannot make partition in Raid 1, and showing a...
View ArticleRe: HP PROLIANT SERVER DL380 GEN9
Hi mate what's the size of your raid when you go into the raid rom configuration setup?
View ArticleZ820 ME Firmware & Management is Disabled in BIOS
I want to updgrade from Win 7 to Win 10.I'm advised it's prudent to upgrade the BIOS/Firmware before doing so.I tried using MEInfoWin but all I got were error codes. Further investigation in the bios...
View Articlecan not install windows 7 on new Elite desktop 800G2
Hello everyone I recently purchased a new PC and I am trying to reinstall windows 7 (64bit).The PC boots off the DVD with no problems but when it reaches the "Select a language" window, the mouse and...
View ArticleRe: reinstall Realtek HP Audio Manager
Thanks for the software tip. VSO Inspector says the drive supports BD-R and BD-RE. That's read-only write once and Recordable Erasable, I believe. It doesn't say what capacities they support. Does it...
View ArticleHP Z640 Raid 1 Setup
Hi All, I have been experiencing a diffcult time setting up Raid 1 storage group on my newly purchase HP Z640. I'm using the configured PCIe SSD drive for the OS (Win10 64 bit) and added 2 WD 6TB Red...
View ArticleRe: reinstall Realtek HP Audio Manager
Hi, It should list BD-R DL if it supports writing to 50Gb discs. Regards, DP-K
View ArticleClik here to view.
Re: reinstall Realtek HP Audio Manager
You would think so. But as you can see by the attached screenshot, the software lists two columns under "Write Features": the ones that are supported are checked (like BD-R and BD-RE). The ones that...
View ArticleRe: reinstall Realtek HP Audio Manager
Hi, If I think of anything else, I'll post back to this thread. Regards, DP-K
View ArticleRe: reinstall Realtek HP Audio Manager
Could this be the solution? See column three of the Disc Compatibility table. http://support.hp.com/us-en/document/c00247346
View ArticleRe: HP Z600 System board / Motherboard that supports x5670 processors?
The Z600 460840-003 supports both the 55xx and 56xx Xeon processors. As you discovered, the 460840-001 only supports the 55xx Xeons. I am not sure about the 460840-002, but there are other threads in...
View Article