Re: Memory error message 201?
Hi, Thank you very much for the further information, in my case is it then the correct population of the two 4Gb rams is to be populated in DIMM1 (Black) (Channel B #13) and DIMM2 (white) (Channel B...
View ArticleRe: Upgrade HP xw4200
Windows 10 32-bit is outstanding on an xw4200 but just know, you'll need a new video card to run dual monitors if you have the fx1300....strongly recommend the nvidia quadro fx1700, 4 times the memory,...
View ArticleBooting Z800 from P410 controller
I still could not configure my Z800 to boot from P410 controllers (I have 2 in it). I did configure boot volume for the controller, but cannot see it in BIOS and wheh I run Windows setup it says that...
View ArticleRe: SM951 M.2 SSD in a HP Z620
Brian1965, The Samsung SM951 AHCI is just miles better than almost any other SSD that can be used in older systems. I have one in a z420 (E5-1660 v2 / 32GB / Quadro K4200 / Intel 730 480GB) on a Lycom...
View ArticleRe: non LSI or Adaptec PCIe SATA-3 controller card in xw6600 for improved...
I am saving up some cash for a future upgrade to a either Z800 or a Z600, perhaps if the circumstances allow a Z420 with Xeon HC (6 core) cpu which already has a 6 Gbps SATA interface in comparison to...
View ArticleRe: Memory error message 201?
You are very welcome, . himaryuk wrote:Hi, Thank you very much for the further information, in my case is it then the correct population of the two 4Gb rams is to be populated in DIMM1 (Black)...
View ArticleRe: Memory error message 201?
Hi, and thank you for your support and further information.I found in the technical reference guide for this model in page section 3.3.1 section memory upgraing that we can install 1GB ram in socket 1,...
View ArticleClik here to view.
Re: Memory error message 201?
Hi,Thank you again, I omitted to send you copy of the page of memroy upgrade in the technical reference manual for this model for your kind comment about my question.Thank you.I look forward to hearing...
View ArticleClik here to view.
Re: SM951 M.2 SSD in a HP Z620
Here are my Passmark scores; Passmark System Rating= 4262 / CPU= 19625 / 2D= 566 / 3D = 4718 / Mem =1807 / Disk = 6629 System: 2x 2670, 64GB 1866MHz, 256GB Samsung SM951 (via ASUS Hyper M.2 X4 Mini)...
View ArticleClik here to view.
Re: SM951 M.2 SSD in a HP Z620
Just to complete the picture, I pulled the Tesla M2090 and Syba SATA III cards from the Z620 and re-run the tests. Here are my new Passmark scores; Passmark System Rating= 4218 / CPU= 19623 / 2D= 571 /...
View ArticleDevicemanager 4.7 SP3 and SP4 break thinclient HPDM agents
After updating to HP Devicemanager 4.7 SP3 (and also SP4) it appears that the update agent task is broken. It reports that the update is successfull, but the client don't connect to Device Manager...
View ArticleRe: Memory error message 201?
You are very welcome, . I would definitely follow the information in Table 3.3.1. You should assure that your new memory matches the specs in Section 3.3, also. If both are correct, there is no...
View ArticleRe: SM951 M.2 SSD in a HP Z620
Brian1965, RAM: When I bought the z620, it had a single 8GB DDR3 1333 ECC module. The memonry perforamnce was very poor with one modeule. There was then the choice as to use 1600 or 1866, but as I...
View ArticleClik here to view.
Re: SM951 M.2 SSD in a HP Z620
This is getting a little bewildering? Just re-fitted the Tesla M2090 GPU and Syba SATA III PCIe cards, re-booted the computer then ran a couple of tests. PassMark now says; Passmark System Rating=...
View ArticleRe: SM951 M.2 SSD in a HP Z620
Brian1965, Memory scores on Passmark are a bit confusing as the memory marks can be much higher on a 16GB system than one having 96GB and so on- all over the map. I'd gotten in the habit over the...
View ArticleRe: Memory error message 201?
Hi and thank you for the valuable information,I was indeed following the information on table 3.3.1 and 3.3.3, so surprised why this error message 201 appears, I was thinking of possibility that the...
View ArticleClik here to view.
Re: non LSI or Adaptec PCIe SATA-3 controller card in xw6600 for improved...
A SSD should be the better choice as the faster access and seek times should provide far better performance compared to HDDs in RAID0. A SATAIII connection should allow you to use the full potential of...
View ArticleRe: non LSI or Adaptec PCIe SATA-3 controller card in xw6600 for improved...
Captain_WD wrote:A SSD should be the better choice as the faster access and seek times should provide far better performance compared to HDDs in RAID0. A SATAIII connection should allow you to use the...
View ArticleRe: Upgrading Z1 Workstation (Mk 1), CPU / GPU options in 2016?
Daniel, The first thing to consider is what aspect of your system would provide the greatest benefit for it's use. If you are doing calaculation-intensive work, it may be the CPU and/or the drives,...
View ArticleRe: Upgrading Z1 Workstation (Mk 1), CPU / GPU options in 2016?
V1per, If I understand your post correctly, you have both a GTX770M and Quadro K2100M in a Z1. If that is the case, I would say that the problem is that the GTX and Quadro drivers are conflicting....
View Article